logo
Products
CASE DETAILS
Home > Cases >
HIKROBOT MV-CB016-10GM-S-W(POE) 1.6MP GigE Board-Level Camera
Events
Contact Us
Miss. Andy
86-0592-5636807
wechat +8618020763272
Contact Now

HIKROBOT MV-CB016-10GM-S-W(POE) 1.6MP GigE Board-Level Camera

2026-11-19

Latest company case about HIKROBOT MV-CB016-10GM-S-W(POE) 1.6MP GigE Board-Level Camera
HIKROBOT MV-CB016-10GM-S-W(POE) 1.6MP GigE Board-Level Camera
Product Overview

The HIKROBOT MV-CB016-10GM-S-W(POE) is a monochrome GigE board-level camera built into the CB Series. It pairs a Sony IMX296 CMOS sensor with global shutter, a 1440 × 1080 resolution, and Power over Ethernet (PoE), so one Cat cable carries both image data and power to a compatible PoE switch or injector.

Board-level construction leaves out the enclosed housing. That trade-off frees mounting space inside OEM machines, embedded vision modules, and compact inspection stations, but it also means the integrator must handle mechanical protection, mounting, and thermal management. This page covers the verified specifications, the engineering limits you should check before purchase, and how the camera fits a typical conveyor inspection build.

Verified Technical Specifications

The figures below follow the CB Series datasheet for the IMX296 monochrome variant. Confirm the latest official datasheet against the exact ordering code before procurement, especially the connector, lens mount, I/O pinout, and PoE implementation.

Parameter Specification
Brand HIKROBOT
Model MV-CB016-10GM-S-W(POE)
Series CB Series
Camera type Board-level area scan camera
Sensor Sony IMX296 CMOS
Sensor format 1/2.9 inch
Pixel size 3.45 μm × 3.45 μm
Shutter Global shutter
Resolution 1440 × 1080 (≈1.56 MP)
Maximum frame rate 65.2 fps @ 1440 × 1080
Imaging mode Monochrome
Dynamic range 74 dB
SNR 41 dB
Gain range 0 dB to 24 dB
Exposure Ultra-short mode: 1 μs–14 μs; standard mode: 15 μs–10 s
Data interface Gigabit Ethernet, compatible with Fast Ethernet; up to 100 m without relay
Power supply 9–24 VDC; PoE supported
Typical power consumption 2.6 W @ 12 VDC
Digital I/O 6-pin connector: 1 non-isolated input, 1 non-isolated output, 1 bidirectional non-isolated I/O
Operating temperature 0 °C to 50 °C
Compliance GigE Vision V2.0, GenICam; CE, FCC, RoHS, KC
Structure Board-level design
Why Global Shutter Matters on a Moving Conveyor

The IMX296 uses a global shutter. Every pixel on the sensor exposes at the same moment within the exposure cycle, unlike a rolling shutter, which reads rows sequentially. On a moving part, that row-by-row timing turns into skew: vertical edges lean, circles stretch into ovals, and measured positions shift depending on travel direction.

Global shutter removes that rolling distortion. It does not remove motion blur. If the part travels several pixels during the exposure window, the image smears regardless of shutter type. The fix is exposure time plus light: shorten the exposure to keep pixel displacement under roughly one pixel, then raise illumination and gain to hold signal. The ultra-short 1 μs exposure mode helps on fast-moving or reflective parts; the standard mode covers slower inspection and low-light scenes.

Typical tasks that rely on consistent image geometry include conveyor inspection, robotic pick-and-place guidance, assembly verification, electronic component alignment, part sorting, and presence detection.

PoE: One Cable for Power and Data

The (POE) suffix means the camera draws power over its Ethernet connection when paired with a compliant PoE source. On a conventional build, the camera needs a separate DC power run alongside the data cable. PoE merges the two, which shortens wiring inside a compact inspection head and gives more freedom when placing the camera away from the control cabinet.

Three constraints apply:

  • The source must supply PoE. A standard data-only Ethernet port will not power the camera. Use a PoE switch, PoE injector, or other approved source that matches the camera's power requirement.
  • Check cable length and drop. GigE reaches about 100 m without a relay. Long PoE runs still suffer voltage drop and signal loss, so verify cable grade, connector, and total length against the installation.
  • Protection and grounding stay on the integrator. PoE does not replace surge protection, proper grounding, shielded cable selection, or network planning.

For OEM builders, the practical payoff is fewer power connections, cleaner cable routing, and easier integration with an existing Ethernet vision network. The camera also accepts 9–24 VDC, so a wired DC supply remains an option where PoE is unavailable or unsuitable.

Where This Camera Fits — and Where It Does Not
Strong fit
  • Compact OEM and embedded vision modules with limited mounting depth.
  • Monochrome inspection based on edges, contours, contrast, orientation, or surface texture.
  • Conveyor and guided-robot tasks where parts move during capture.
  • Multi-camera layouts that benefit from shared Ethernet infrastructure and simplified cabling.
Check before committing
  • Frame rate above 65.2 fps. At full resolution this camera tops out at 65.2 fps. Faster cycling or high-speed freeze-action needs a higher-frame-rate sensor.
  • Color-based defect detection. This is a monochrome model. If the defect relies on hue, paint shade, or color coding, evaluate the color variant or a separate color camera.
  • Harsh environments without protection. The bare board lacks an enclosed housing. Dust, liquids, washdown, heavy vibration, or accidental contact call for an enclosure, mounting bracket, and vibration review.
  • Very small defects at long working distances. Resolution and pixel scale depend on field of view, working distance, and lens magnification. The 1.56 MP frame may not resolve sub-mm defects across a wide view; calculate pixel per defect before signing off.
  • PoE budget on long or high-noise runs. Confirm the power source and cable plan for the actual site.
Hypothetical Build: Small Component Inspection on a Conveyor

This example illustrates how the camera might be evaluated. It is an engineering reference, not a documented customer deployment or a validated performance test.

Production requirements

A line carries small metal and electronic parts through an inspection station. The station must confirm each part is present, correctly oriented, and inside the inspection window; it may also flag surface contamination or selected assembly defects. The camera space is tight, and the builder wants to minimize separate cables routed to the module.

Why this model comes up

The board-level body suits the tight mounting space, the monochrome output handles edge and contrast checks, and the global shutter keeps geometry stable as parts pass. The 1440 × 1080 frame gives about 1.56 million pixels, but whether that is enough depends on the field of view, working distance, lens magnification, part size, and smallest defect. Shoot representative parts under real lighting before locking the design.

Reference system architecture
  • Camera: HIKROBOT MV-CB016-10GM-S-W(POE).
  • Lens: selected to match the 1/2.9-inch sensor, target field of view, and working distance; mount must be confirmed against the official model drawing.
  • Lighting: LED arrangement chosen for contrast on the actual material (direct, diffuse, backlight, bright-field, or dark-field).
  • Power: compliant PoE switch or injector sized for the camera and any other powered devices on the segment.
  • Host: industrial PC running image acquisition and processing.
  • Software: HIKROBOT MVS or another GigE Vision / GenICam-compatible vision application.
  • Controller: PLC or motion controller that receives pass/fail results and triggers reject or alarm logic.
Suggested acquisition parameters to test

Treat these as starting points, not guaranteed settings:

  • Trigger from an encoder or proximity sensor so exposure lines up with part position.
  • Start exposure in the 10–50 μs range for typical conveyor speeds, then shorten until motion displacement stays under one pixel; use the ultra-short mode for faster travel.
  • Set gain conservatively (0–12 dB) and raise light first; the 24 dB ceiling exists for low-signal cases, not as a default.
  • Measure pixel scale on a calibrated target and verify the smallest defect covers at least 2–3 pixels across, per the vision application's tolerance.
Inspection sequence

Acquire the image, preprocess it, define the region of interest, extract features, analyze position and orientation, verify presence or absence, and output a result. Fail parts go to the PLC for rejection or operator notification. Detection limits must be proven on production samples at line speed; lab images on clean parts do not substitute for that test.

Optics and Lighting Selection

Sensor specs alone do not determine inspection quality. The lens and illumination set the contrast and resolution the software works from.

Lens choice

Match the lens to sensor format, field of view, working distance, required detail, lens resolution, distortion budget, available space, and mechanical mount. The actual mount on the MV-CB016-10GM-S-W(POE) — M12, C-mount, or otherwise — must be read from the official drawing. Do not assume every M12 or C-mount lens fits without confirming the camera configuration.

Monochrome imaging

Monochrome drops the color filter array and delivers higher effective sensitivity and resolution for intensity-based tasks. It fits presence checks, edge and contour analysis, contrast inspection, orientation verification, and basic dimensional measurement. It cannot distinguish colors, so revisit the camera choice if hue is part of the defect definition.

Lighting methods
Lighting method Typical use
Direct LED General part imaging, bright-field surface detail
Diffuse lighting Reducing specular reflection on glossy or curved surfaces
Backlighting Silhouette, contour, and outer-diameter inspection
Bright-field Surface features and contrast-based defect detection
Dark-field Scratches, edges, embossed marks, and surface irregularities

Reflective metal, transparent parts, and dark substrates each behave differently. Test the arrangement on production samples before committing to a fixed light fixture.

Software and Communication Compatibility

The camera follows GigE Vision V2.0 and GenICam, the two standards that let compliant cameras talk to acquisition software and processing hardware.

GigE Vision defines image transfer and camera control over Gigabit Ethernet. The camera's network connection to the host carries frames and control commands; plan the segment bandwidth, especially with multiple cameras.

GenICam standardizes how software reads and configures camera features. Exposure, gain, trigger mode, pixel format, and acquisition settings are exposed through this interface, subject to the firmware implementation.

HIKROBOT MVS handles camera discovery, configuration, live acquisition, and integration development. Before adopting third-party vision software, verify its GigE Vision and GenICam support against this exact model and firmware version.

Basic integration workflow
  1. Install the compatible camera driver and MVS or SDK.
  2. Connect the camera to a suitable Gigabit Ethernet network.
  3. Supply power through the approved PoE arrangement or a 9–24 VDC wired connection.
  4. Configure network address, exposure, gain, and trigger settings.
  5. Confirm stable image acquisition and transmission.
  6. Connect the image-processing application.
  7. Hand inspection results to the PLC or machine controller.
  8. Validate the full system under production conditions, including line speed and lighting variation.
Board-Level Camera vs. Enclosed Industrial Camera
Factor Board-level camera Conventional enclosed camera
Mechanical structure Bare board, custom mounting Integrated housing
OEM integration Flexible for customized equipment Suited to standardized installations
Installation space Supports compact layouts Dimensions set by enclosure
Mechanical protection Protection must be added by the integrator Housing provides physical protection
Thermal management Handled inside the machine design Depends on camera housing and operating conditions
Cabling Requires planning for board connectors Often uses standardized camera connectors
Maintenance Access needed inside the enclosure Can be replaced as a complete unit
Best fit Embedded and customized vision systems General-purpose industrial vision installs

The CB Series body saves space and gives layout freedom, but in dusty, wet, vibrating, or contact-prone environments it needs added guarding and a reviewed mounting approach.

Common Industrial Applications
  • Electronic component inspection: presence detection, alignment checks, and visual verification on small parts.
  • Conveyor-based inspection: global-shutter capture of moving components, tuned with the right exposure and illumination.
  • Automated assembly verification: confirm parts are present and seated before the next operation.
  • Robotic positioning: image-based position and orientation for guided pick-and-place.
  • Compact OEM vision modules: embedded inspection heads where mounting depth and cable count matter.

Each category still requires optical, mechanical, electrical, and software validation on real parts.

Procurement and Integration Checklist

Before ordering the MV-CB016-10GM-S-W(POE), confirm:

  • Exact ordering model, including the POE suffix.
  • Sony IMX296 monochrome sensor configuration.
  • 1440 × 1080 resolution and 65.2 fps maximum under the intended operating mode.
  • Global shutter operation.
  • PoE requirement and compatible power source; whether a backup DC connection is needed.
  • GigE Vision V2.0 and GenICam support in the planned software.
  • Actual lens mount and optical compatibility.
  • Mechanical drawing for mounting and enclosure integration.
  • Connector pinout and digital I/O wiring.
  • Operating temperature and installation environment.
  • Driver and SDK compatibility for the host platform.
  • Latest manufacturer datasheet before final purchase.

For replacement projects, compare mechanical dimensions, mounting holes, network configuration, and software compatibility with the existing camera. Matching resolution and interface does not guarantee a drop-in replacement.

Frequently Asked Questions
What is the HIKROBOT MV-CB016-10GM-S-W(POE)? It is a monochrome GigE board-level industrial camera in the CB Series, built around the Sony IMX296 global-shutter sensor and supporting PoE power delivery.
What sensor and resolution does it use? Sony IMX296 CMOS, 1/2.9-inch format, 3.45 μm pixels, 1440 × 1080 resolution, about 1.56 MP, monochrome.
What does PoE buy you on this camera? A compatible PoE source supplies power over the Ethernet cable, removing the separate DC power run in installations that support it. The camera still accepts 9–24 VDC as an alternative.
Why choose global shutter over rolling shutter? Global shutter exposes the whole sensor at once, reducing skew when parts move during capture. Exposure time and lighting still have to be set to control motion blur.
Will it work with third-party vision software? The camera supports GigE Vision V2.0 and GenICam. Compatibility with a specific third-party package still depends on driver, firmware, and feature support, so verify before integration.
What frame rate can I expect? Up to 65.2 fps at 1440 × 1080 full resolution. Higher speeds require a different camera.
Conclusion

The MV-CB016-10GM-S-W(POE) pairs a 1.56 MP IMX296 global-shutter sensor, 65.2 fps full-resolution capture, GigE Vision, and PoE in a compact board-level body. It targets embedded OEM inspection, conveyor part checks, and monochrome vision guidance where space and cabling are constrained.

Deployment still comes down to the right lens, stable illumination, correct exposure and trigger setup, and a network that carries the required frame rate. Before integration, confirm the exact configuration against the official datasheet, check PoE compatibility, and review the optical and mechanical layout with production samples.

Request the MV-CB016-10GM-S-W(POE) datasheet or discuss your optical, lens, and lighting configuration with our vision engineering team.
sitemap |  Privacy Policy | China Good Quality SICK Laser Sensor Supplier. Copyright © 2025-2026 Xiamen ZhiCheng Automation Technology Co., Ltd . All Rights Reserved.